Servo motor test equipment
Universal Servo Motor Test Bench in India: Multi-Brand Servo Motor Testing and Encoder Alignment
Star Automations owns and operates a universal servo motor test bench in India, built on the Mitchell Electronics TI-5000JX feedback test and alignment platform and the TI-3000JX run test system. We use it to test encoders and resolvers, set encoder alignment after repair, read encoder memory and run the repaired servo motor without its original drive.

What is a universal servo motor test bench?
A universal servo motor test bench is test equipment that checks the feedback device and runs the motor for many motor makes, instead of needing a separate drive from each manufacturer. A servo motor depends on its encoder or resolver. If the feedback signal or its alignment to the rotor is wrong, the motor will not run correctly on the machine, even when the winding and bearings are good.
| Equipment at Star Automations | Role | What it does |
|---|---|---|
| Mitchell Electronics TI-5000JX | Feedback test and alignment platform | Tests encoders and resolvers, checks and sets feedback alignment, reads encoder memory |
| Mitchell Electronics TI-3000JX | Run test system | Runs permanent magnet brushless servo motors with many feedback types after repair, without the motor maker's own drive |
| WinTI5000JX PC software | Operator interface | Shows counts, commutation, encoder status and angles on screen and saves the test report |
| Feedback and power test cables, adapter modules | Connection to the motor | Match the tester to the connector and signal type of each motor and encoder |
| Unidrive M701 test bench | Drive test | Tests repaired Control Techniques drives |
Which encoders, resolvers and motor makes can be tested?
The platform has test software for the feedback families below. The table follows the manufacturer's published software list for the TI-5000JX and TI-3000JX. The test for a specific motor depends on its feedback device and connector, so send the make, model and a nameplate photo and we confirm before you ship.
| Feedback family | Example encoder series | Typical motor makes | Tests |
|---|---|---|---|
| Incremental encoder (A, B, Z with commutation) | Quadrature incremental encoders with commutation outputs | Many servo motor makes | Count, phase angle, commutation, alignment, run test |
| Resolver | Most resolver types | Many servo motor makes | Angle reading, output level, alignment, run test |
| Parallel absolute encoder | Parallel absolute, binary and Gray code | Older absolute encoder motors | Code and line state check |
| Heidenhain EnDat | ECN1313, EQN1325, ECI and EQI series | Siemens, B&R, Bosch Rexroth, Kollmorgen, Baumüller | Alignment, memory test, run test |
| Sick Stegmann Hiperface | SKS36, SKM36, SRS50, SRM50, SNS, SEK, SEL | Allen-Bradley MPL, MPF, MPS and 1326AB, Berger Lahr, Elau, Fagor, Schneider BMH, Control Techniques, Bosch Rexroth MSK | Alignment, memory test, memory programming, run test |
| Tamagawa serial | TS5643, TS5645, TS5647, TS5648, TS5667, TS5668, TS5669, TS5778 | Matsushita, Toshiba, Shibaura, Nachi, Shinko, Kobelco | Alignment, run test |
| Mitsubishi serial | OSA, OSE, OBA and OAH series | Mitsubishi | Alignment, run test |
| Fanuc pulsecoder | Fanuc incremental, absolute and serial pulsecoders | Fanuc | Alignment, run test |
| Yaskawa | Incremental, C-channel and absolute encoders | Yaskawa | Alignment, absolute encoder checks |
| Sanyo Denki and Sumtak | Sanyo Denki serial and incremental, Sumtak REC and REM | Sanyo Denki, Nachi | Alignment, run test |
| Kawasaki | H20, M21 and HE-02 | Kawasaki robot motors | Alignment, run test |
| Bosch Rexroth and Indramat digital | Digital servo feedback on MDD, MHD and MKD families, MKD resolver boards | Bosch Rexroth, Indramat | Alignment, memory test, run test |
| BiSS, SSI and MFE | BiSS serial, Hengstler SSI, MFE family | Unico, Bosch Rexroth MSM | Test and alignment |
Brand and series names are used only to identify the motors and feedback devices. Star Automations is an independent multi-brand repair company and is not an OEM service centre.
What tests are done on the bench?
Each test answers one question about the feedback device or the motor. The tests used depend on the motor and the fault.
| Test | What it checks | Fault it finds |
|---|---|---|
| Count test | Counts per revolution against the expected value | Missing or extra pulses, damaged code disc, stuck bits |
| Phase angle test | Phase relationship between incremental channels | Signal distortion and poor signal quality |
| Line level check | Signal voltage levels on each line | Weak or dead output channels |
| Commutation check | Commutation tracks or absolute position against the rotor | Wrong commutation, motor runs rough or draws high current |
| Feedback alignment | Encoder or resolver angle against the rotor magnet position | Alignment lost after bearing, winding or encoder work |
| Encoder status and memory test | Status flags and motor data stored in the encoder | Encoder errors, corrupt or blank motor data |
| Run test | Motor running under its own feedback after repair | Faults that show only when the motor turns |

How is a servo motor tested and aligned after repair?
The feedback device is tested first, the alignment is set with the rotor locked, and the motor is then run. The steps below are the usual order.
- Identify the motor and feedbackThe nameplate, encoder type and connector are identified and the matching test cable and software are selected.
- Test the feedback deviceCounts, signal levels, commutation and encoder status are checked. Encoder memory is read and saved where the motor stores data in the encoder.
- Repair the motorBearings, winding, brake, connectors or the feedback device are repaired or replaced as the findings show.
- Lock the rotor and set alignmentThe rotor is held at a known electrical position with DC current and the encoder or resolver is set to the correct angle.
- Run testThe motor is run on the run test system under its own feedback.
- Report and dispatchA report with findings, parts replaced and test readings goes back with the motor.

What do I send to get a servo motor tested or repaired?
Send the details in the first column on WhatsApp or the quote form. We confirm repairability before you ship. We do not publish fixed prices.
| Your need | You send | We deliver |
|---|---|---|
| Servo motor repair | Make, model, fault and nameplate photo | Findings first, then repair, alignment, run test and report |
| Encoder or resolver test only | Motor or feedback device, encoder type | Feedback test results |
| Encoder alignment after your own repair | Motor with the feedback device fitted | Alignment set and run test |
| Batch or repeat work for repair shops and OEMs | List of models and quantities | Test and alignment plan with a quotation |
Frequently asked questions
What test equipment does Star Automations use for servo motors?
Star Automations uses the Mitchell Electronics TI-5000JX feedback test and alignment platform and the TI-3000JX run test system, with WinTI5000JX PC software. The equipment is in our own workshops in India. A Unidrive M701 bench is used for repaired Control Techniques drives.
Can you test a servo motor without its original drive?
Yes. The TI-3000JX run test system runs permanent magnet brushless servo motors with many feedback types, so the motor can be run after repair without the machine or the motor maker's own drive. Send the make and model and we confirm the test for your motor.
Which servo motor brands and encoders can be tested?
The platform has test software for incremental encoders, resolvers and serial encoder families such as Heidenhain EnDat, Sick Stegmann Hiperface, Tamagawa, Mitsubishi, Fanuc, Yaskawa, Sanyo Denki and Kawasaki. The test for a specific motor depends on the feedback device, so send the nameplate and we confirm before you ship.
What is encoder alignment and why is it needed after repair?
A servo drive needs the encoder or resolver position to match the rotor magnet position. If the feedback device is removed for a bearing or winding repair, that relationship is lost. The alignment is checked and set again on the test bench, so the motor produces correct torque when it returns to the machine.
Can you read or program encoder memory?
For motor families that store motor data in the encoder, the encoder memory is read and saved as a report. Where the platform has a programming module for that motor family, memory data can be written to a replacement encoder. Send the motor model to confirm.
Do I get a test report?
Yes. The test software saves a report for the feedback device, and a printed report with the findings, parts replaced and test readings goes back with the motor.
Where is the test bench located?
Servo motor inspection, repair, encoder alignment and dispatch are done at our Puducherry, Chennai and Bengaluru sites. Motors can be sent by courier from anywhere in India or from overseas.
How do I get a quotation?
Send the motor make, model and fault with a nameplate photo on WhatsApp +91 97866 22233 or the quote form. We confirm repairability and reply with a quotation. Warranty is set per customer on the quote. We do not publish fixed prices.
Related servo motor services
- Servo motor repair
- Universal servo motor repair equipment
- Encoder alignment
- Servo motor testing India
- Resolver and encoder testing and alignment
- Servo motor and drive diagnosis
- Discontinued servo motor repair
- Servo motor repair FAQ
- Servo repair partner programme
- OEM repair alternatives
- PCB repair test equipment
- Request a quote
Call or WhatsApp +91 97866 22233, or email info@starautomations.com.