Emergency: same day
For a line-down motor, where the fault and parts allow. WhatsApp us before you send it so the bench is kept free.
Since 2000 · 3,000+ customers
Mitsubishi · Servo drive repair · India
We repair Mitsubishi MELSERVO drives and amplifiers at component level: power stage, DC bus, feedback input, control and I/O faults. Every repaired drive is tested with a servo motor under load before dispatch and returned with a printed test report. Send the drive label and the alarm code, such as AL.16 or AL.32, to get a quote. Repair warranty is 3 months to 1 year, stated on each quotation.

*Where the fault and parts allow. Every repaired unit returns with a printed test report.
Send a photo of the nameplate first. We confirm whether the motor is repairable, and the quote, the same working day.
For a line-down motor, where the fault and parts allow. WhatsApp us before you send it so the bench is kept free.
Repair, encoder alignment and test, counted from the day the motor reaches the bench and the quote is approved.
Full repair, encoder alignment, run test under load and a printed test report.
Send the full model number from the label, for example MR-J2S-200A.







A drive alarm tells you where to look, not always what failed. Overcurrent can be the power stage, the gate drive, the motor or the cable.
Code meanings differ between series. Always confirm against the manual for your exact model.
Check the encoder cable and connector first, then test the encoder.
Can be the drive power stage, the motor or the cable. Disconnect the motor and see if the alarm stays.
Absolute encoder battery or backup. Check the battery before replacing parts.
Check the regeneration resistor and the supply voltage.
Alarm guides: Mitsubishi AL.16 and AL.20 · Mitsubishi AL.32 overcurrent · Absolute encoder battery · Mitsubishi AL.25 · Mitsubishi AL.50 · Full Mitsubishi MR-J4 alarm list · MR-J2S and MR-J3 alarm list · Scheduled maintenance: fan, battery, capacitor
After component-level repair, the drive is powered up on a test rig, the power stage and feedback circuits are checked, and the drive is run with a servo motor under load. Your drive comes back with its own settings and serial history, and a printed test report.
If the motor is the real cause, the drive repair alone will not hold. When the alarm points to feedback or overcurrent, send the motor too: see Mitsubishi servo motor repair and Mitsubishi encoder repair. We are an independent multi-brand repair company, not an OEM service centre.
For a stopped line. Send the label photo and alarm code first.
Once the fault is confirmed on inspection.
Planned repair with the full test and a printed report.
Time depends on the fault and on parts. What affects repair cost.
You can send a drive from anywhere in India. Talk to us before you courier, so the unit is expected and logged on arrival.
WhatsApp a clear photo of the drive label, the alarm code and what the machine was doing when it failed.
We tell you whether we can test and repair that model before anything is shipped.
Courier the drive, with the motor if the alarm points to feedback or overcurrent, to our Chennai or Puducherry bench.
The drive is opened and inspected. You get the findings and a quote before work starts.
Repaired at component level, tested with a servo motor under load, then dispatched with a printed test report.
The Mitsubishi MR-J2S-40A (400 W) and MR-J2S-70A (750 W) are MR-J2S general-purpose AC servo amplifiers, a discontinued Mitsubishi Electric line that many machines still run. Star Automations repairs both at component level and bench-tests each repaired drive before dispatch. If repair is not worthwhile, we plan the upgrade to the MR-J4 series, checking motor, encoder, parameters and wiring so the machine restarts with minimal change. We are an independent multi-brand repair company, not a Mitsubishi Electric service centre.
Typical reasons these two drives reach us: encoder communication alarms, overcurrent after a power-stage failure, regeneration and overvoltage faults, worn DC bus capacitors and no display at power-up. Send the full label (including the suffix after MR-J2S-40A or MR-J2S-70A) and the alarm code shown.
Star Automations is an independent multi-brand repair company, not an OEM service centre. We repair discontinued Mitsubishi MELSERVO drives including the MR-J2S-100A (1 kW) and MR-J3-70A (0.75 kW), including units that no longer have manufacturer repair support, with bench tests and load checks.
Yes. We repair power-stage and control faults and test the drive.
Yes, and we can plan migration to MR-J4 with parameter mapping if you want to upgrade.
Star Automations is an independent multi-brand repair company, not an OEM service centre. We repair MELSERVO MR-J2S-70A amplifiers and Mitsubishi GOT1000 GT1675M-VTBA 10.4" panels with bench testing.
Yes. Backlight, touch and display faults are repaired.
One route for servo motors, encoders and drives. You see the price before any work starts, and the report before the unit leaves our bench.
EmergencySame day*
Urgent3 working days
Standard7 working days
*Where the fault and parts allow. Turnaround counts from when the unit reaches our bench and the quote is approved.
More on the FAQ page.
Yes. We repair MR-J2S-40A (400 W) and MR-J2S-70A (750 W) servo amplifiers at component level and bench-test them before dispatch. Send the full label and the alarm code on WhatsApp +91 97866 22233.
Yes, the MR-J2S series is discontinued. The current Mitsubishi family is MR-J4. We repair your existing drive, or plan the upgrade to MR-J4 after checking motor, encoder, parameters and wiring.
Yes. We repair Mitsubishi servo drives and amplifiers at component level, test them with a servo motor under load and return them with a printed test report. Send the label photo and alarm code on WhatsApp and we confirm repairability before you courier.
No. Star Automations is an independent multi-brand repair company, not an OEM service centre. The brand name only describes the equipment we repair.
It is an encoder initial communication alarm on MELSERVO drives. The cause is often the encoder, its cable or a connector, but a drive input fault is also possible. See our AL.16 and AL.20 guide.
Yes. When the alarm points to feedback or overcurrent we test the drive with the motor, so a motor fault does not bring the alarm back.
The drive label photo, the alarm code, the motor nameplate and what the machine was doing at the time of failure.
WhatsApp a photo to +91 97866 22233, or email info@starautomations.com.