Since 2000 · 3,000+ customers

Servo motor test equipment

Universal Servo Motor Test Bench in India: Multi-Brand Servo Motor Testing and Encoder Alignment

Star Automations owns and operates a universal servo motor test bench in India, built on the Mitchell Electronics TI-5000JX feedback test and alignment platform and the TI-3000JX run test system. We use it to test encoders and resolvers, set encoder alignment after repair, read encoder memory and run the repaired servo motor without its original drive.

Star Automations universal servo motor test bench with laptop test software, DC power supply and bench test instruments
Since 2000servo motor repair as our core work
TI-5000JXfeedback test and alignment platform
TI-3000JXrun test system
3 sitesPuducherry, Chennai, Bengaluru
Multi-brandindependent, not an OEM service centre

What is a universal servo motor test bench?

A universal servo motor test bench is test equipment that checks the feedback device and runs the motor for many motor makes, instead of needing a separate drive from each manufacturer. A servo motor depends on its encoder or resolver. If the feedback signal or its alignment to the rotor is wrong, the motor will not run correctly on the machine, even when the winding and bearings are good.

Equipment at Star AutomationsRoleWhat it does
Mitchell Electronics TI-5000JXFeedback test and alignment platformTests encoders and resolvers, checks and sets feedback alignment, reads encoder memory
Mitchell Electronics TI-3000JXRun test systemRuns permanent magnet brushless servo motors with many feedback types after repair, without the motor maker's own drive
WinTI5000JX PC softwareOperator interfaceShows counts, commutation, encoder status and angles on screen and saves the test report
Feedback and power test cables, adapter modulesConnection to the motorMatch the tester to the connector and signal type of each motor and encoder
Unidrive M701 test benchDrive testTests repaired Control Techniques drives

Which encoders, resolvers and motor makes can be tested?

The platform has test software for the feedback families below. The table follows the manufacturer's published software list for the TI-5000JX and TI-3000JX. The test for a specific motor depends on its feedback device and connector, so send the make, model and a nameplate photo and we confirm before you ship.

Feedback familyExample encoder seriesTypical motor makesTests
Incremental encoder (A, B, Z with commutation)Quadrature incremental encoders with commutation outputsMany servo motor makesCount, phase angle, commutation, alignment, run test
ResolverMost resolver typesMany servo motor makesAngle reading, output level, alignment, run test
Parallel absolute encoderParallel absolute, binary and Gray codeOlder absolute encoder motorsCode and line state check
Heidenhain EnDatECN1313, EQN1325, ECI and EQI seriesSiemens, B&R, Bosch Rexroth, Kollmorgen, BaumüllerAlignment, memory test, run test
Sick Stegmann HiperfaceSKS36, SKM36, SRS50, SRM50, SNS, SEK, SELAllen-Bradley MPL, MPF, MPS and 1326AB, Berger Lahr, Elau, Fagor, Schneider BMH, Control Techniques, Bosch Rexroth MSKAlignment, memory test, memory programming, run test
Tamagawa serialTS5643, TS5645, TS5647, TS5648, TS5667, TS5668, TS5669, TS5778Matsushita, Toshiba, Shibaura, Nachi, Shinko, KobelcoAlignment, run test
Mitsubishi serialOSA, OSE, OBA and OAH seriesMitsubishiAlignment, run test
Fanuc pulsecoderFanuc incremental, absolute and serial pulsecodersFanucAlignment, run test
YaskawaIncremental, C-channel and absolute encodersYaskawaAlignment, absolute encoder checks
Sanyo Denki and SumtakSanyo Denki serial and incremental, Sumtak REC and REMSanyo Denki, NachiAlignment, run test
KawasakiH20, M21 and HE-02Kawasaki robot motorsAlignment, run test
Bosch Rexroth and Indramat digitalDigital servo feedback on MDD, MHD and MKD families, MKD resolver boardsBosch Rexroth, IndramatAlignment, memory test, run test
BiSS, SSI and MFEBiSS serial, Hengstler SSI, MFE familyUnico, Bosch Rexroth MSMTest and alignment

Brand and series names are used only to identify the motors and feedback devices. Star Automations is an independent multi-brand repair company and is not an OEM service centre.

What tests are done on the bench?

Each test answers one question about the feedback device or the motor. The tests used depend on the motor and the fault.

TestWhat it checksFault it finds
Count testCounts per revolution against the expected valueMissing or extra pulses, damaged code disc, stuck bits
Phase angle testPhase relationship between incremental channelsSignal distortion and poor signal quality
Line level checkSignal voltage levels on each lineWeak or dead output channels
Commutation checkCommutation tracks or absolute position against the rotorWrong commutation, motor runs rough or draws high current
Feedback alignmentEncoder or resolver angle against the rotor magnet positionAlignment lost after bearing, winding or encoder work
Encoder status and memory testStatus flags and motor data stored in the encoderEncoder errors, corrupt or blank motor data
Run testMotor running under its own feedback after repairFaults that show only when the motor turns
Mitchell TI-3000JX run test system during a servo motor run test
Run test of a repaired servo motor on the TI-3000JX run test system at Star Automations.

How is a servo motor tested and aligned after repair?

The feedback device is tested first, the alignment is set with the rotor locked, and the motor is then run. The steps below are the usual order.

  1. Identify the motor and feedbackThe nameplate, encoder type and connector are identified and the matching test cable and software are selected.
  2. Test the feedback deviceCounts, signal levels, commutation and encoder status are checked. Encoder memory is read and saved where the motor stores data in the encoder.
  3. Repair the motorBearings, winding, brake, connectors or the feedback device are repaired or replaced as the findings show.
  4. Lock the rotor and set alignmentThe rotor is held at a known electrical position with DC current and the encoder or resolver is set to the correct angle.
  5. Run testThe motor is run on the run test system under its own feedback.
  6. Report and dispatchA report with findings, parts replaced and test readings goes back with the motor.
Setting feedback commutation alignment on a servo motor after repair
Setting feedback alignment on a servo motor after repair.

What do I send to get a servo motor tested or repaired?

Send the details in the first column on WhatsApp or the quote form. We confirm repairability before you ship. We do not publish fixed prices.

Your needYou sendWe deliver
Servo motor repairMake, model, fault and nameplate photoFindings first, then repair, alignment, run test and report
Encoder or resolver test onlyMotor or feedback device, encoder typeFeedback test results
Encoder alignment after your own repairMotor with the feedback device fittedAlignment set and run test
Batch or repeat work for repair shops and OEMsList of models and quantitiesTest and alignment plan with a quotation

Frequently asked questions

What test equipment does Star Automations use for servo motors?

Star Automations uses the Mitchell Electronics TI-5000JX feedback test and alignment platform and the TI-3000JX run test system, with WinTI5000JX PC software. The equipment is in our own workshops in India. A Unidrive M701 bench is used for repaired Control Techniques drives.

Can you test a servo motor without its original drive?

Yes. The TI-3000JX run test system runs permanent magnet brushless servo motors with many feedback types, so the motor can be run after repair without the machine or the motor maker's own drive. Send the make and model and we confirm the test for your motor.

Which servo motor brands and encoders can be tested?

The platform has test software for incremental encoders, resolvers and serial encoder families such as Heidenhain EnDat, Sick Stegmann Hiperface, Tamagawa, Mitsubishi, Fanuc, Yaskawa, Sanyo Denki and Kawasaki. The test for a specific motor depends on the feedback device, so send the nameplate and we confirm before you ship.

What is encoder alignment and why is it needed after repair?

A servo drive needs the encoder or resolver position to match the rotor magnet position. If the feedback device is removed for a bearing or winding repair, that relationship is lost. The alignment is checked and set again on the test bench, so the motor produces correct torque when it returns to the machine.

Can you read or program encoder memory?

For motor families that store motor data in the encoder, the encoder memory is read and saved as a report. Where the platform has a programming module for that motor family, memory data can be written to a replacement encoder. Send the motor model to confirm.

Do I get a test report?

Yes. The test software saves a report for the feedback device, and a printed report with the findings, parts replaced and test readings goes back with the motor.

Where is the test bench located?

Servo motor inspection, repair, encoder alignment and dispatch are done at our Puducherry, Chennai and Bengaluru sites. Motors can be sent by courier from anywhere in India or from overseas.

How do I get a quotation?

Send the motor make, model and fault with a nameplate photo on WhatsApp +91 97866 22233 or the quote form. We confirm repairability and reply with a quotation. Warranty is set per customer on the quote. We do not publish fixed prices.