Emergency: same day
For a line-down motor, where the fault and parts allow. WhatsApp us before you send it so the bench is kept free.
Since 2000 · 3,000+ customers
Yaskawa · Servo drive repair · India
We repair Yaskawa SERVOPACK servo drives and amplifiers (Sigma-7, Sigma-V, Sigma-II and older) at component level: power stage, DC bus, feedback input, control and I/O faults. Every repaired drive is tested with a servo motor under load before dispatch and returned with a printed test report. Send the drive label and the alarm code, such as A.100 or A.C90, to get a quote. Repair warranty is 3 months to 1 year, stated on each quotation.

*Where the fault and parts allow. Every repaired unit returns with a printed test report.
Send a photo of the nameplate first. We confirm whether the motor is repairable, and the quote, the same working day.
For a line-down motor, where the fault and parts allow. WhatsApp us before you send it so the bench is kept free.
Repair, encoder alignment and test, counted from the day the motor reaches the bench and the quote is approved.
Full repair, encoder alignment, run test under load and a printed test report.
Send the full model number from the label, for example SGD7S-2R8A00A002.




A drive alarm tells you where to look, not always what failed. Overcurrent can be the power stage, the gate drive, the motor or the cable.
Code meanings differ between series. Always confirm against the manual for your exact model.
Can be the drive power stage, the motor or the cable. Disconnect the motor and see if the alarm stays.
Check the encoder cable and connector first, then test the encoder.
Absolute encoder battery or backup data. Check the battery before replacing parts.
Check the regeneration resistor and the supply voltage.
Alarm guides: Yaskawa A.100 overcurrent · Yaskawa A.C90 encoder · Yaskawa A.810 backup · Yaskawa A.300 · Yaskawa A.710
Sigma-V and Sigma-7 SERVOPACKs (SGDV, SGD7S, SGD7W) show three-character codes such as A.100 or A.C90. Sigma-II SERVOPACKs (SGDM, SGDH) show two-character codes such as A.10 or A.C9. Code meanings can differ between series and firmware, so confirm against the manual for your exact model before replacing parts.
| What it means | Sigma-V / Sigma-7 (SGDV, SGD7S, SGD7W) | Sigma-II (SGDM, SGDH) | First check |
|---|---|---|---|
| Overcurrent or heat sink overheat | A.100 | A.10 | Disconnect the motor cable. If the alarm stays with the motor off, suspect the drive power stage. If it clears, check the motor and cable insulation. |
| Regeneration error / regenerative overload | A.300 / A.320 | A.30 / A.32 | Check the regeneration resistor, its wiring and the parameter for resistor capacity. |
| Overvoltage / undervoltage | A.400 / A.410 | A.40 / A.41 | Check the incoming supply and the deceleration time. Repeated alarms with normal supply point to the DC bus circuit. |
| Overspeed | A.510 | A.51 | Check encoder wiring and the motor phase order (U, V, W). |
| Overload (instantaneous / continuous) | A.710 / A.720 | A.71 / A.72 | Check for mechanical binding, a brake not releasing, or an undersized motor. |
| Absolute encoder backup error | A.810 | A.81 | Replace the encoder battery, then reset the absolute encoder. |
| Encoder communication error | A.C90 | A.C9 | Check the encoder cable and connector first, then test the encoder. Swap with a known-good cable if you have one. |
| Position error overflow | A.d00 | A.d0 | Check the mechanics and gain settings, then the encoder. |
If the alarm keeps coming back after these checks, send the drive, and the motor too when the alarm points to feedback or overcurrent. To test the motor yourself first, see how to check an AC servo motor.
After component-level repair, the drive is powered up on a test rig, the power stage and feedback circuits are checked, and the drive is run with a servo motor under load. Your drive comes back with its own settings and serial history, and a printed test report.
If the motor is the real cause, the drive repair alone will not hold. When the alarm points to feedback or overcurrent, send the motor too: see Yaskawa servo motor repair and Yaskawa encoder repair. We are an independent multi-brand repair company, not an OEM service centre.
For a stopped line. Send the label photo and alarm code first.
Once the fault is confirmed on inspection.
Planned repair with the full test and a printed report.
Time depends on the fault and on parts. What affects repair cost.
You can send a drive from anywhere in India. Talk to us before you courier, so the unit is expected and logged on arrival.
WhatsApp a clear photo of the drive label, the alarm code and what the machine was doing when it failed.
We tell you whether we can test and repair that model before anything is shipped.
Courier the drive, with the motor if the alarm points to feedback or overcurrent, to any of our three sites in Puducherry, Chennai and Bengaluru, or ask us to arrange pickup.
The drive is opened and inspected. You get the findings and a quote before work starts.
Repaired at component level, tested with a servo motor under load, then dispatched with a printed test report.
Star Automations is an independent multi-brand repair company, not an OEM service centre. We repair discontinued Yaskawa Sigma-II servopacks such as the SGDM-10ADA (1 kW, 200-230 V) with power-stage and control repair, parameter backup and load testing.
Yes. We repair and test it on the bench; we can also plan an upgrade to Sigma-7.
Star Automations is an independent multi-brand repair company, not an OEM service centre. We repair Yaskawa Sigma-5 SGDV servopacks such as SGDV-5R5A01A and SGDV-120A01A, and Sigma-II SGDM servopacks such as SGDM-15ADA.
Use the manufacturer manual for the exact order number. If the unit is faulty, send us the label and the fault description and we will advise whether repair, upgrade or migration is the better route.
The repair cost depends on the exact order number and the fault found on the bench. Send the order number and a photo of the label on WhatsApp and we reply with a repair quote.
Star Automations is an independent multi-brand repair company, not an OEM service centre. We repair Yaskawa Sigma-II SGDH-15AE (1.5 kW) servopacks and plan upgrade to Sigma-7.
Yes. We repair and test it.
One route for servo motors, encoders and drives. You see the price before any work starts, and the report before the unit leaves our bench.
EmergencySame day*
Urgent3 working days
Standard7 working days
*Where the fault and parts allow. Turnaround counts from when the unit reaches our bench and the quote is approved.
More on the FAQ page.
Yes. We repair Yaskawa servo drives and amplifiers at component level, test them with a servo motor under load and return them with a printed test report. Send the label photo and alarm code on WhatsApp and we confirm repairability before you courier.
No. Star Automations is an independent multi-brand repair company, not an OEM service centre. The brand name only describes the equipment we repair.
It is an encoder communication alarm. The cause is often the encoder, its cable or a connector, but a drive input fault is also possible. See our A.C90 guide.
Yes. When the alarm points to feedback or overcurrent we test the drive with the motor, so a motor fault does not bring the alarm back.
The drive label photo, the alarm code, the motor nameplate and what the machine was doing at the time of failure.
Both are encoder communication alarms. A.C90 is the code on Sigma-V and Sigma-7 drives; A.C9 is the code on Sigma-II drives (SGDM, SGDH). The cause is often the encoder, its cable or a connector, but a drive feedback input fault is also possible.
Overcurrent or heat sink overheat. Disconnect the motor and see if the alarm stays. If it stays, the drive power stage is the likely cause.
Yes, in most cases. We repair the unit at component level, so the drive does not need to be in current production.
WhatsApp a photo to +91 97866 22233, or email info@starautomations.com.