Since 2000 · 3,000+ customers

Home / ABB ACS1000, ACS2000 and IGCT

Medium-voltage and IGCT drive repair

ABB ACS1000, ACS2000 and IGCT drive repair in India

Star Automations repairs ABB ACS1000, ACS2000 and ACS800 drive modules, plus IGCT gate-driver and control boards, at component level from its Puducherry factory and bench tests them before dispatch. Star is an independent repair house, not an OEM service partner. Send the drive type and fault code on WhatsApp +91 97866 22233 and the team will reply with the repair route.

Send your part number for the price

Star Automations does not list prices on this page because every unit and fault is different. Send the model or part number, the fault and a photo, and the price comes with the quote. Every repair carries a warranty; terms are on the quote.

What Star Automations repairs

EquipmentTypical items repaired
ABB ACS1000 and ACS1000iControl boards, gate-driver boards, interface boards, power supplies, fan and monitoring boards
ABB ACS2000Control and I/O boards, gate-driver boards, power supplies
ABB ACS800Control boards, I/O boards, gate-driver boards, power supplies, inverter module electronics
IGCT gate units and driversGate-unit boards, driver electronics, diagnostics of the gate-drive path

Common faults and what we check

SymptomWhat we check
Drive trips with a fault code at startControl board, gate-driver path and power supply rails
DC link does not build or chargeCharging circuit, interface and measurement boards
IGCT or gate-driver fault messagesGate-unit board, driver electronics, fibre and signal path
Control panel dead or no communicationControl board, power supply, communication interface
Cooling or fan alarmsFan monitoring board, sensor inputs, supply rails
Intermittent trips under loadMarginal components, connectors, measurement boards

How the repair and bench test works

Repair routeFour stages: receive, diagnose, repair and bench test, return.ReceiveDiagnoseRepairBench test and return
  1. Intake and logThe unit is logged with photos and the reported fault.
  2. InspectionVisual and thermal inspection for burnt parts and damage.
  3. Signature checkQMax QT-205 signature analysis compared with known-good behaviour.
  4. Component repairFaulty components are replaced at board level.
  5. Bench testThe repaired unit is bench tested before dispatch.
  6. Return with test noteThe unit goes back with a note of what was repaired.

Repair, tested replacement or exchange

RouteWhat it means
RepairYour own unit is repaired at component level and returned.
Tested replacementA tested unit is supplied where one is available.
ExchangeYour faulty unit is swapped against a tested unit, subject to availability.

Hardware repair and bench test of the boards; the plant commissions and re-validates the full drive on site. Star Automations is an independent repair house, not an OEM service partner.

Frequently asked questions

What do you repair on ABB ACS1000, ACS2000 and IGCT equipment?

Star Automations repairs the boards, modules and power supplies listed in the table above at component level. Send the model and the fault, and the team replies with the repair route.

Is Star Automations an OEM service partner?

No. Star Automations is an independent repair house, not an OEM service partner. Repairs are done at component level in Puducherry.

How do I start a repair?

Use the Send your part number button or WhatsApp +91 97866 22233 with the model, the fault description and a photo of the unit.

Do you test the unit after repair?

Yes. Each repaired unit is bench tested before dispatch. Boards are also checked with a QMax QT-205 signature analyser against known-good behaviour where it applies.

What about the price?

Prices are not listed here because each unit is different. Send the part number or model and the fault, and the price comes with the quote.

Does the repair carry a warranty?

Every repair carries a warranty; terms are on the quote.

Can you supply a tested replacement or an exchange unit?

Where a tested unit is available it can be supplied as a tested replacement or an exchange against your faulty unit. Availability depends on the model.

Does the plant still need to re-validate the system?

Yes. Hardware repair and bench test of the boards; the plant commissions and re-validates the full drive on site.

Where is the work done and which cities do you cover?

Work is done at the Puducherry factory. Star Automations also has offices in Chennai, Bengaluru, Hyderabad and Delhi, and accepts units shipped from anywhere in India.

What if the board is obsolete or the fault is not found at first?

Star Automations works at component level, so an obsolete board is repaired instead of replaced where possible. If a fault needs more investigation, the team tells you before going further.