Since 2000 · 3,000+ customers

Home / Siemens Perfect Harmony and Robicon

Medium-voltage drive repair

Siemens Perfect Harmony and Robicon drive repair in India

Star Automations repairs Siemens Perfect Harmony and legacy Robicon medium-voltage drive electronics at component level from its Puducherry factory, including control, interface and power cell boards, and bench tests them before dispatch. Star is an independent repair house, not an OEM service partner. Send the drive model and fault message on WhatsApp +91 97866 22233 for the repair route.

Send your part number for the price

Star Automations does not list prices on this page because every unit and fault is different. Send the model or part number, the fault and a photo, and the price comes with the quote. Every repair carries a warranty; terms are on the quote.

What Star Automations repairs

EquipmentTypical items repaired
Siemens Perfect HarmonyControl boards, interface boards, power cell electronics, power supplies
Robicon medium-voltage drivesLegacy control and interface boards, power supplies, gate-driver electronics
Cell and gate-driver electronicsDriver boards, bypass and monitoring electronics
Operator panels and I/ODisplay and keypad units, I/O boards, communication interfaces

Common faults and what we check

SymptomWhat we check
Drive trips on a cell or power faultPower cell electronics, driver boards, supply rails
Drive will not start or ride throughControl board, interface boards, measurement inputs
Communication or fibre-optic faultInterface boards, communication path, connectors
Operator panel blank or unresponsiveDisplay, keypad and panel supply
Intermittent faults after long serviceAgeing components, connectors, marginal solder joints
Spare board needed for a legacy driveRepair of the existing board or a tested replacement

How the repair and bench test works

Repair routeFour stages: receive, diagnose, repair and bench test, return.ReceiveDiagnoseRepairBench test and return
  1. Intake and logThe unit is logged with photos and the reported fault.
  2. InspectionVisual and thermal inspection for burnt parts and damage.
  3. Signature checkQMax QT-205 signature analysis compared with known-good behaviour.
  4. Component repairFaulty components are replaced at board level.
  5. Bench testThe repaired unit is bench tested before dispatch.
  6. Return with test noteThe unit goes back with a note of what was repaired.

Repair, tested replacement or exchange

RouteWhat it means
RepairYour own unit is repaired at component level and returned.
Tested replacementA tested unit is supplied where one is available.
ExchangeYour faulty unit is swapped against a tested unit, subject to availability.

Hardware repair and bench test of the boards; the plant commissions and re-validates the full drive on site. Star Automations is an independent repair house, not an OEM service partner.

Frequently asked questions

What do you repair on Siemens Perfect Harmony and Robicon equipment?

Star Automations repairs the boards, modules and power supplies listed in the table above at component level. Send the model and the fault, and the team replies with the repair route.

Is Star Automations an OEM service partner?

No. Star Automations is an independent repair house, not an OEM service partner. Repairs are done at component level in Puducherry.

How do I start a repair?

Use the Send your part number button or WhatsApp +91 97866 22233 with the model, the fault description and a photo of the unit.

Do you test the unit after repair?

Yes. Each repaired unit is bench tested before dispatch. Boards are also checked with a QMax QT-205 signature analyser against known-good behaviour where it applies.

What about the price?

Prices are not listed here because each unit is different. Send the part number or model and the fault, and the price comes with the quote.

Does the repair carry a warranty?

Every repair carries a warranty; terms are on the quote.

Can you supply a tested replacement or an exchange unit?

Where a tested unit is available it can be supplied as a tested replacement or an exchange against your faulty unit. Availability depends on the model.

Does the plant still need to re-validate the system?

Yes. Hardware repair and bench test of the boards; the plant commissions and re-validates the full drive on site.

Where is the work done and which cities do you cover?

Work is done at the Puducherry factory. Star Automations also has offices in Chennai, Bengaluru, Hyderabad and Delhi, and accepts units shipped from anywhere in India.

What if the board is obsolete or the fault is not found at first?

Star Automations works at component level, so an obsolete board is repaired instead of replaced where possible. If a fault needs more investigation, the team tells you before going further.