Marine automation repair
Kongsberg and Norcontrol marine automation repair in India
Star Automations repairs Kongsberg and Norcontrol marine and offshore automation boards, I/O modules, operator station electronics and power supplies at component level in Puducherry and bench tests them before dispatch. Star is an independent repair house, not an OEM service partner. Send the unit type and fault description on WhatsApp +91 97866 22233 for the repair route.
Send your part number for the price
Star Automations does not list prices on this page because every unit and fault is different. Send the model or part number, the fault and a photo, and the price comes with the quote. Every repair carries a warranty; terms are on the quote.
What Star Automations repairs
| Equipment | Typical items repaired |
|---|---|
| Kongsberg automation and control modules | CPU and controller boards, I/O modules, communication boards, power supplies |
| Norcontrol bridge and engine-room automation | Control and interface modules, alarm and I/O boards, power supplies |
| Operator stations and panels | Display units, keypads, panel electronics |
| Power supply and distribution units | Switching supplies, distribution and monitoring boards |
Common faults and what we check
| Symptom | What we check |
|---|---|
| Module shows a fault or drops off the network | Communication board, supply rails, connectors |
| Alarm or I/O channel not reading | I/O front end, signal conditioning, field interface |
| Operator station dead or display faulty | Display, backlight, power board |
| Controller restarts or hangs | CPU board, memory, power supply stability |
| Intermittent fault with vessel motion or vibration | Connectors, solder joints, marginal components |
| Spare module needed for an older system | Repair of the existing module or a tested replacement |
How the repair and bench test works
- Intake and logThe unit is logged with photos and the reported fault.
- InspectionVisual and thermal inspection for burnt parts and damage.
- Signature checkQMax QT-205 signature analysis compared with known-good behaviour.
- Component repairFaulty components are replaced at board level.
- Bench testThe repaired unit is bench tested before dispatch.
- Return with test noteThe unit goes back with a note of what was repaired.
Repair, tested replacement or exchange
| Route | What it means |
|---|---|
| Repair | Your own unit is repaired at component level and returned. |
| Tested replacement | A tested unit is supplied where one is available. |
| Exchange | Your faulty unit is swapped against a tested unit, subject to availability. |
Hardware repair and bench test of the modules; the operator re-validates the system function on board. Star Automations is an independent repair house, not an OEM service partner.
Frequently asked questions
What do you repair on Kongsberg and Norcontrol equipment?
Star Automations repairs the boards, modules and power supplies listed in the table above at component level. Send the model and the fault, and the team replies with the repair route.
Is Star Automations an OEM service partner?
No. Star Automations is an independent repair house, not an OEM service partner. Repairs are done at component level in Puducherry.
How do I start a repair?
Use the Send your part number button or WhatsApp +91 97866 22233 with the model, the fault description and a photo of the unit.
Do you test the unit after repair?
Yes. Each repaired unit is bench tested before dispatch. Boards are also checked with a QMax QT-205 signature analyser against known-good behaviour where it applies.
What about the price?
Prices are not listed here because each unit is different. Send the part number or model and the fault, and the price comes with the quote.
Does the repair carry a warranty?
Every repair carries a warranty; terms are on the quote.
Can you supply a tested replacement or an exchange unit?
Where a tested unit is available it can be supplied as a tested replacement or an exchange against your faulty unit. Availability depends on the model.
Does the plant still need to re-validate the system?
Yes. Hardware repair and bench test of the modules; the operator re-validates the system function on board.
Where is the work done and which cities do you cover?
Work is done at the Puducherry factory. Star Automations also has offices in Chennai, Bengaluru, Hyderabad and Delhi, and accepts units shipped from anywhere in India.
What if the board is obsolete or the fault is not found at first?
Star Automations works at component level, so an obsolete board is repaired instead of replaced where possible. If a fault needs more investigation, the team tells you before going further.