Bengaluru · Wireless RF testing and job work
IoT and Telematics Device RF Verification in Bengaluru
RF verification for IoT, telematics and wearable device makersWe check the Wi-Fi and Bluetooth radios of finished IoT, tracker and telematics devices and boards by cable on a LitePoint IQxel-M, and record each unit. Pilot runs and volume lots are welcome.
Important: This is an in-house RF verification and test record service for design checks, production, validation, returned-unit analysis and post-repair testing. It is not NABL-accredited testing, and it is not WPC, BIS, FCC, CE or any other regulatory certification. Our records do not replace an accredited laboratory's report. For type approval or certification, please use an accredited or notified laboratory.
Why finished-device RF checks matter
Antenna, board and assembly variation can change what a device actually transmits. A cabled check on the finished unit shows the radio as built, per unit.
What we check on connected devices
- Wi-Fi and Bluetooth transmit power and signal quality
- Frequency error and spectral mask
- Receiver sensitivity and packet error rate, with a receive test mode
Within the technologies and bands in range, depending on installed options.
Test mode and fixture requirements
What you supply: the devices or boards, test firmware or a vendor test tool that puts the radio into transmit and receive test modes, a golden sample, RF connector or fixture access, and your test plan with limits. Without a test mode we cannot drive the radio.
We can help define the cabled fixture and the script on request.
Pilot batch and lot testing
Step 1
We sign your NDA if you need one.
Step 2
You send a golden unit, samples and the test firmware or vendor tool.
Step 3
We agree the test plan and limits in writing.
Step 4
We test a pilot batch and share the records.
Step 5
We run the full lots under the agreed plan.
Step 6
You receive the per-unit and per-lot records.
What we do not do
- Cellular signalling tests
- AIS-140, BIS, WPC or other approvals, or any certification
Our records are not regulatory certification.
What you receive
A per-unit and per-lot test record (PDF with a CSV data file): unit ID, set conditions, measured values, your limits, pass or fail, instrument model, software version, date and operator name. We report what we measure.
For power profiling, see battery drain testing; for dispatch safety checks, see hipot testing.
Frequently asked questions
What is wireless connectivity RF testing?
RF testing of a Wi-Fi or Bluetooth device measures what its radio transmits and how well it receives, for example output power, signal quality (EVM), spectral mask, frequency error and receiver sensitivity. We connect each device to the tester by cable in a shielded setup, run your test mode, and record every measured value against your limits.
Do you take bulk orders and production overflow work?
Yes, for corporate customers. You send a golden sample and your test plan, we agree a pilot batch, then we run volume lots with a test record for every unit. We work to your limits and your test firmware. Lot sizes, schedule and conditions are agreed in writing for each lot, and we sign an NDA on request.
What do I need to supply for testing?
Please supply the devices or boards, a way to put each into transmit and receive test modes through firmware or a vendor test tool, a golden sample, an RF connector or fixture, and your test plan with limits. Without a test mode we cannot drive the radio. We can help define the fixture and the script on request.
Are your test records certificates (NABL, WPC, BIS, FCC or CE)?
No. We provide in-house RF verification and a test record. We are not a NABL-accredited laboratory, and our records are not WPC, BIS, FCC, CE or any other regulatory certification. For type approval or certification, please use an accredited or notified laboratory. Our records support your own pre-checks and production quality control.
Request a pilot batch quote
Tell us what you need to test: device type, technologies, quantity per lot and per month, and your limits or test plan. We reply on WhatsApp or by email to agree the next step.
WhatsApp: +91 97866 22233. Website: www.starautomations.com. Address: 1st Floor, 40, Goshala Rd, Garudachar Palya, Mahadevapura, Bengaluru, Karnataka 560048.
Message received
Our team replies by email or WhatsApp. For urgent requests, WhatsApp +91 97866 22233.
Star Automations provides in-house testing and test records. We are not a NABL-accredited laboratory, and our records are not regulatory certification. Star Automations is an independent multi-brand repair company and is not an OEM service centre.